一、技術指標
1、測量范圍：2～50%
2、顯示：LCD液晶顯示
3、檔位調整：50～500g/m2（1-5檔）
4、掃描深度：0～50mm
5、精度：±0.5%
6、體積、重量：120×60×26(mm),150g
二、使用方法
選擇檔位開關：
1檔：紙箱、瓦楞紙板
2檔：50克以下紙張、漿板紙等
3檔：瓦楞紙、書寫紙、牛皮紙、箱板紙
4檔：新聞紙、白板紙、涂布紙
5檔：銅版紙、復印紙、傳真紙
由于紙張結構不同，其介電系數亦不同；以上檔位為建議檔位，如有誤差，請進行對比校驗。如：測量某一已知水分為8%的紙張，調整檔位開關為4檔時，所測數字顯示為08.0，則以后再測量同類紙張時應將檔位選為4檔。
三、注意事項
1、由于KT-50型紙張水分儀電磁波穿透深度達50mm，所以測量紙張的平均水分時，要求被測紙張或紙箱疊加厚度不得小于50mm。
2、如儀表開機后顯示不在00.0±00.5范圍以內，請將電池后蓋打開取出電池，在電池盒內側有一零位調節器。正值不到零位，逆時針調節；反之，順時針調節。
3、由于本紙張水分儀采用電磁波感應方式進行測量，測量時儀器周圍或底部不得有金屬物或其它感應物，否則會對測量精度有所影響。
PAPER MOISTURE TESTER KT-50
Introduction
The electronic meter allows the measurement of the moisture in the paper in the size 120×60×26mm and the weight of 150g.It is a battery-operated pin instrument,fully transistorized and operates on a pure dielectric constant measurement with HF(High Frequency) waves.The method of measurement is based on a balance system,which measures the DK-value(dielectric-value) of the moist material,after precious deduction of the DK-value of the dry material and thus the pure moisture content is indicated.
FEATURES
KT-50 paper moisture meter produced by Italy KLORTNER company permits to measure the moisture content of many kinds of paper products ranging from 50 to 500g/m²,quickly by simply contacting and eliminate paper damage.
The precise dielectric constant measurement with HF waves can get the moisture content of the depth of 50mm at most.
After being used for 40 seconds,KT-50 moisture meter will automatically turn off to retrench the power supply for protecting itself.
KT-50 paper moisture meter will remind you of low voltage as well.
TECHNICAL DATA
Measuring Range:0%~50%
Resolution:0.1%
Repetition Accuracy: ±0.5%
Display:3½LCD
Scanning Depth:50mm(1.96 inch) at most
Density Range:50 to 500g/m²
Work Environment: -5℃ to 50℃
Power Supply:9V(6F22) shut off after used 40 seconds automatically
Dimension:120×60×26mm
Weight:150g
APPLICATION
Before measuring,get a right selector according to the paper species table or paper density.
With the sensor of KT-50 touching nothing,press“ON”button.Turn carefully“ZERO”button in the battery cover,till the readings on the screen is between 00.0±00.5.
With the sensor of the meter,touch the wood to be measured fully.As soon as the meter is in touch with the paper surface,the moisture content is indicated.
NOTICE
The paper to be measured should be bigger than the sensor of the meter.
Nothing else can be placed under the paper to be measured,otherwise the measurement will be inaccuracy.
If the thickness of the material to be measured is lower than 50 mm,to avoid wrong readings,it is sufficient to hold the items without its bottom touching anyting.
- 溫馨提示：為規避購買風險，建議您在購買前務必確認供應商資質與產品質量。
- 免責申明：以上內容為注冊會員自行發布，若信息的真實性、合法性存在爭議，平臺將會監督協助處理，歡迎舉報